TRAXXAS X-MAXX Rear Spiral Bevel Gear - STXM1200R by GPM  [STXM1200R]

TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R
Price:
CAD$64.92
Brand:
GPM
Model:
STXM1200R
GTIN:
4894538275094
Condition:
Brand New
1 Reviews
Write a review
alt="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R" title="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R"
alt="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R" title="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R"
alt="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R" title="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R"
alt="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R" title="TRAXXAS X-MAXX Retail Hard Steel Rear Spiral Bevel Gears - GPM STXM1200R"

Rear spiral bevel for X-MAXX drivetrain

The STXM1200R rear spiral bevel gear is an aftermarket RC-scale replacement made for TRAXXAS X-MAXX drivetrains. This hard steel gear is produced to match the form and fit of the original X-MAXX rear bevel set without promising specific performance increases.

Install this component when replacing worn or damaged rear bevel gears or when checking drivetrain wear as part of routine maintenance. The text emphasises compatibility, material, and the role of the part within an RC drivetrain, while leaving model-specific installation details to chassis manuals and experienced technicians.

During installation confirm gear mesh, inspect bearings and shaft fit, and apply the correct lubrication and endplay before testing the vehicle. Treat this item as an aftermarket drivetrain component for model-scale use.

Specifications

  • Item: Rear spiral bevel gears
  • Material: Hard steel
  • Model Number: STXM1200R
  • Compatibility: TRAXXAS X-MAXX

Select the STXM1200R rear bevel when replacing or inspecting TRAXX1200R rear components on TRAXXAS X-MAXX platforms and follow chassis-specific fitment guidance for correct setup.

This item is compatible with

  • TRAXXAS XMAXX
  • TRAXXAS X MAXX 8S Monster Truck

 

Product Reviews
1 Reviews
rating
Good material quality vs stock. But I think the ring gear needs to be designed better! As the meshing is too loose. The ring gear needs to be a bit thicker like the stock one to move the teeth closer to the pinion. Shimming the pinion helps a little bit.

Will STXM1200R fit directly into my X-MAXX rear housing?

STXM1200R is listed for TRAXXAS X-MAXX compatibility. Verify dimensions against your existing bevel set and confirm shaft and bearing interfaces before final installation.

How should I check gear mesh when installing this part?

Set mesh using shims or the chassis procedure, rotate the drivetrain by hand, and ensure teeth engage smoothly with minimal backlash and no binding.

Is special lubrication needed for a hard steel bevel?

Use a quality gear grease suitable for steel components and recheck after a short break-in run. Avoid overpacking the gear area which can trap debris.

What should I inspect while the gear is out?

Check pinion alignment, bearing play, shaft runout, and any signs of wear on surrounding gears before reassembly to ensure reliable operation.

Copyright © 2008-2026 rcjaz.ca All rights reserved