TRAXXAS Slash 4x4 Low-cg Front Gearbox Protector SLA330LCG by GPM  [SLA330LCG]

TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG
Price:
CAD$68.72
Brand:
GPM
Model:
SLA330LCG
GTIN:
4894538074178
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG" title="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG"
alt="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG" title="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG"
alt="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG" title="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG"
alt="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG" title="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG"
alt="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG" title="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG"
alt="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG" title="TRAXXAS Slash 4x4 Aluminium Front Gear Box Protector - 1pc set (For Slash 4x4 Low-cg 68086-21 Version) - GPM SLA330LCG"

Low-profile Front Gearbox Guard for Slash 4x4

This aluminium front gear box protector is an RC-scale accessory engineered for the TRAXXAS Slash 4x4 Low-cg 68086-21 version, designed to add a rigid protective layer over the front gearbox area. It is a direct-fit aftermarket component intended to reduce contact damage to the gearbox housing while keeping access for routine service.

In practical setup and tuning terms, the protector shields the gearbox from rocks, curbs and chassis scrapes that can disturb gear alignment and reduce drive efficiency. The aluminium construction gives greater dimensional stability than stock plastic covers, helping to maintain consistent gear mesh under load without changing factory mounting points.

Specifications

  • Item Front Gear Box Protector
  • Material Aluminium
  • Model Number SLA330LCG
  • Compatibility TRAXXAS Slash 4x4 Low-cg 68086-21 Version

For builders who want a durable, low-profile gearbox guard that fits the stock front assembly of the Slash 4x4 Low-cg, this aluminium protector offers protection without altering drivetrain geometry.

This item is compatible with

  • TRAXXAS SLASH 4X4 LOW CG

Will this install on the Slash 4x4 Low-cg 68086-21 as-is?

Yes, the protector is specified for the Slash 4x4 Low-cg 68086-21 and is made for direct installation on the stock front gearbox mounting points.

Do I need to re-check gear mesh after fitting?

Verify gear mesh during installation; the aluminium part is stiff but does not intentionally alter gearbox geometry, so only minor mesh tweaks are typically needed if any play is found.

How should I care for the aluminium surface?

Wipe off grit after runs and rinse away corrosive salts; aluminium resists rust but the finish can wear over time, so inspect contact points regularly.

Will this add noticeable weight to the front?

The added mass is small for this scale and designed for protection rather than changing balance, so handling changes are minimal in normal use.

Copyright © 2008-2026 rcjaz.ca All rights reserved