TRAXXAS Slash 4X4 Front C Hub 7075 Alloy SLA019N by GPM  [SLA019N]

TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N
Price:
CAD$40.61
Brand:
GPM
Model:
SLA019N
GTIN:
4894538387933
Condition:
Brand New
Write a review
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"
alt="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N" title="TRAXXAS SLASH 4X4 LOW-CG 7075 Alloy Front C Hub - GPM SLA019N"

Front C-hub upgrade for Slash 4X4 handling

This SLA019N front C hub is an RC-scale replacement part designed for TRAXXAS Slash 4X4 and several related 1/10 4WD platforms. Machined from 7075 alloy, it locates the knuckle arm on a bearing instead of a shaft hole to reduce play and promote smoother steering feedback. Multiple upper tie rod mounting holes let you fine-tune steering roll center and toe characteristics without changing other suspension parts.

Installation follows the stock mounting points at the front c-hub area and uses the supplied hardware for a direct swap. The bearing-mounted knuckle location requires correct bearing seating and typical thread-lock on the metal screws where applicable. This part is intended for hobby RC use only and is compatible with the models listed below.

Packing includes

  • C-Hub - 1pcs
  • King Pin - 1pcs
  • Grade 12.9 black Round Head Screws 3x14 - 1pcs
  • Grade 12.9 black Round Head Screws 3x16 - 1pcs

Original Name / Part No:

6832

Compatible Models

  • TRAXXAS-SLASH 4X4 LOW-CG-68086-21
  • TRAXXAS 1/10 RUSTLER 4X4 VXL-67076-4
  • TRAXXAS 1/10 4WD HOSS 4X4 VXL 3S-90076-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74064-4
  • TRAXXAS 1/10 Ford Fiesta ST Rally-74054-4
  • TRAXXAS 1/10 Rustler 4X4-67064-1
  • TRAXXAS 1/10 Rustler 4X4-67064-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68086-4
  • TRAXXAS 1/10 Slash 4X4-68054-1
  • TRAXXAS 1/10 Slash 4X4-68054-61
  • TRAXXAS 1/10 Slash 4X4 VXL-68286-4
  • TRAXXAS 1/10 Stampede 4X4 VXL-67086-4
  • TRAXXAS 1/10 Rustler 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-67097-4
  • TRAXXAS 1/10 Slash 4X4 Ultimate-68277-4

Fit this 7075 C hub to reduce knuckle slop and sharpen front-end response; move the upper tie rod to tune steering characteristics for track or rough surfaces, and confirm bearing seating and screw torque during installation.

Will SLA019N fit my Slash 4X4 VXL chassis code?

Check the Compatible Models box above for the exact chassis codes. If your Slash 4X4 VXL code appears in that list, this hub is listed as compatible.

Are replacement bearings required with this hub?

The kit supplies the C-hub hardware but not wheel or knuckle bearings. Inspect existing bearings and replace any that show play to ensure proper bearing seating in the knuckle location.

What thread locker and torque should I use?

Use a medium-strength thread locker on metal-to-metal fasteners and follow your chassis manual for recommended torque values; avoid over-tightening bearings in their seat.

How will 7075 alloy change handling?

7075 alloy increases front-end stiffness compared with softer alloys, which reduces flex and helps produce crisper steering feedback when paired with correct geometry settings.

Copyright © 2008-2026 rcjaz.ca All rights reserved