TRAXXAS Revo Servo Mount Set - Alloy Front & Rear - TRV024 by GPM  [TRV024]

TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024
Price:
CAD$20.94
Brand:
GPM
Model:
TRV024
GTIN:
4894538204995
Condition:
Brand New
Write a review
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"
alt="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024" title="TRAXXAS Revo /Revo 3.3 Alloy Front& Rear Completed Servo Mount With Screws - 2prs set - GPM TRV024"

Alloy front and rear servo mounts for Revo platforms

This GPM TRV024 assembly supplies front and rear alloy servo mounts as finished units with mounting screws, made for hobby TRAXXAS Revo vehicles. The set replaces factory plastic mounts to increase clamp rigidity and preserve servo alignment under load, helping steering remain consistent during setup and rough use.

Installation is simple for experienced modelers: the completed mounts fit common servo footprints and use the supplied screws for direct swap with stock parts. When installing, confirm servo horn clearance and pushrod geometry before final tightening, then cycle full steering travel to ensure there is no binding at suspension extremes.

Sold as an aftermarket upgrade, these alloy mounts strengthen the mechanical interface between the servo and chassis rather than changing servo torque or speed; they are handy when fitting higher performance servos or when a firmer mount is needed for aggressive driving and track tuning.

Compatible Models

  • TRAXXAS Revo
  • Revo 3.3

Can I bolt these on in place of the plastic mounts?

They are made for direct replacement using the supplied screws, but always verify servo footprint and clearances before final assembly.

Will upgrading to alloy affect servo speed or torque?

No, these mounts improve structural support and alignment only; they do not alter the servo's electrical performance.

How do I avoid binding after fitting?

Set the servo horn and pushrod with the suspension at full droop and full compression, then check for smooth travel through the whole steering arc before locking bolts.

Copyright © 2008-2026 rcjaz.ca All rights reserved