Tamiya GF01 38mm Steel Front/Rear CVD Shafts 12x6mm Hex GF1238SADT by GPM  [GF1238SADT]

Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT
Price:
CAD$28.18
Brand:
GPM
Model:
GF1238SADT
GTIN:
4894538035407
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"
alt="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT" title="Tamiya GF01 Steel #45 Front/Rear CVD Shaft (38mm) With 12x6mm Hex Adapters - 1pr set - GPM GF1238SADT"

38mm steel CVDs for GF01 overview

This aftermarket pair of front and rear CVD shafts is offered as a direct steel replacement for standard plastic or softer metal drives used on the Tamiya GF01 platform. The shafts are made from #45 steel, measure 38mm, and the set includes 12x6mm hex adapters to mate with common GF01 wheel hex mounts.

Functionally these shafts keep the original GF01 fitment points while delivering higher torsional stiffness and improved wear life compared with softer materials. They suit hobby 1/10 touring and off-road GF01 variants where the stock driveshaft length and hex adapter dimensions match the listed specification.

Installation notes: verify your vehicle uses GF01 standard CVD length and the 12x6mm wheel hex interface before fitting, inspect pin retention and bearing condition during reassembly, and perform a short low-speed test to confirm free rotation and absence of binding.

Specifications

  • Item: Front/Rear CVD shaft set
  • Material: Steel #45
  • Model Number: GF1238SADT
  • Compatibility: Tamiya GF01
  • Length: 38mm
  • Includes: 12x6mm hex adapters
  • Quantity: 1 pr set

For GF01 builders wanting a straightforward steel swap with standard 12x6mm hex compatibility, this 38mm shaft set provides a direct-fit durability upgrade; always confirm fit on your specific GF01 variant before heavy use.

Will these replace stock GF01 CVDs without chassis modification?

They are designed to match GF01 mounting points and 12x6mm hex interface, so they should fit as a direct swap when your chassis uses standard GF01 CVD length and hex size.

Do the shafts include wheel hex adapters?

Yes, the set ships with 12x6mm hex adapters to interface with common GF01 wheel hex mounts; other small fasteners such as pins or bearings are not included.

Any special break-in required for steel shafts?

No special break-in is required; inspect for burrs, apply light lubrication to splines if present, and check retention hardware after initial runs to ensure proper seating.

Which GF01 variants are supported?

These are specified for GF01 where the stock CVD length is 38mm and the wheel hex interface is 12x6mm; confirm measurements on your specific variant before purchase.

Copyright © 2008-2026 rcjaz.ca All rights reserved