Kyosho Mini-Z AWD Rear Knuckle Arm Holder Alloy, Toe Out -0.2mm 0.6mm MZA031R-0206 by GPM  [MZA031R-0206]

Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206
Price:
CAD$6.63
Brand:
GPM
Model:
MZA031R-0206
GTIN:
4894538121902
Condition:
Brand New
Write a review
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"
alt="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206" title="Kyosho Mini-Z AWD Alloy Rear Knuckle Arm Holder (Toe Out -0.2mm, Thick 0.6mm) - 1pc GPM Design - GPM MZA031R-0206"

Aluminium rear knuckle mount for Mini-Z AWD setups

This alloy rear knuckle arm holder is made to fit Kyosho Mini-Z AWD rear assemblies and is supplied as a single replacement piece. It sets a nominal rear Toe Out of -0.2mm with a 0.6mm plate thickness for small, repeatable rear toe adjustments during setup and track tuning.

The alloy construction focuses on consistent fit and dimensional stability under normal model use. Verify fitment on your specific Mini-Z AWD chassis before final assembly and confirm the toe setting matches your handling goals.

Fitting tips: check orientation and torque for the mounting screws, ensure the mating surfaces seat correctly, and run the suspension through full travel to confirm wheel clearance. Supplied quantity: 1 pcs.

Will this fit every Mini-Z AWD rear knuckle?

This part is designed for Mini-Z AWD rear layouts; compare the part geometry with your chassis code to confirm compatibility before purchasing.

How big an effect does the -0.2mm toe out give?

The -0.2mm change is subtle and intended for fine trimming of rear stability rather than major handling shifts. Use it alongside other setup tweaks for balanced results.

What should I inspect after installation?

After fitting, verify screw torque, check for binding across suspension travel, and confirm tyre clearance at full droop and compression.

Copyright © 2008-2026 rcjaz.ca All rights reserved