HPI Bullet 3.0 Rear Anti-bending Plate BMT009 for WR8 tuning by GPM  [BMT009]

HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009
Price:
CAD$13.77
Brand:
GPM
Model:
BMT009
Please kindly input your name and email address, we will inform you once we have the restocking.
Or you may find similar product under the
category
Write a review
alt="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009" title="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009"
alt="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009" title="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009"
alt="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009" title="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009"
alt="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009" title="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009"
alt="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009" title="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009"
alt="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009" title="HPI Bullet 3.0 Mt And St (Nitro Engines) Alloy Rear Anti-bending Plate - 1pc set (For WR8 / Bullet 3.0) - GPM BMT009"

Rear reinforcement plate for Bullet 3.0

This aluminium rear anti-bending plate is an aftermarket replacement designed for HPI Bullet 3.0 and WR8 platforms, supplied as a single alloy piece. It targets nitro touring car layouts where reducing rear flex helps maintain suspension geometry under load.

The plate uses the stock rear mounting points so no chassis cutting is required, replacing the standard brace with a stiffer connection between the rear tower and the chassis. In use this reduces unpredictable toe and camber shifts during cornering, helping you dial in rear traction and balance more reliably.

Installation tips: verify compatibility with your chassis code and torque fasteners evenly to avoid stress points. Check fuel tank and exhaust clearances on nitro setups before final tightening. This part is intended as a direct one-piece replacement for compatible Bullet 3.0 and WR8 rear assemblies.

Compatible Models

  • WR8
  • Bullet 3.0

Will BMT009 fit every Bullet 3.0 rear tower?

Fitment is for the listed Bullet 3.0 and WR8 variants that use the same rear mounting pattern; confirm your chassis code before ordering to ensure a match.

Does the alloy plate change handling a lot?

It increases rear stiffness so alignment changes are more predictable under load, which helps you refine rear toe and camber for improved consistency rather than radically altering handling.

Any special tools required to fit it?

Standard metric drivers and a torque driver for even tightening are sufficient; check clearance around fuel and exhaust on nitro cars before final assembly.

Copyright © 2008-2026 rcjaz.ca All rights reserved