GPM TRX-4 MERCEDES-BENZ G500 Pendulum Axle Weight 23mm Hex TRX4023XBZ - RC Spare Part  [TRX4023XBZ]

TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ
Price:
CAD$44.83
Brand:
GPM
Model:
TRX4023XBZ
GTIN:
4894538326758
Condition:
Brand New
Write a review
alt="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ" title="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ"
alt="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ" title="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ"
alt="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ" title="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ"
alt="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ" title="TRAXXAS TRX4 MERCEDES-BENZ Brass Pendulum Wheel Knuckle AXLE Weight+23mm Hex - 12pc set - GPM TRX4023XBZ"

Brass pendulum wheel weight for TRX-4 G500

This RC-scale pendulum wheel weight set is made for TRX4 MERCEDES-BENZ platforms and fits to the outer case of the front and rear knuckle arms, installing onto a 23mm hex. A central bearing with a Delrin collar and a tapered pendulum profile keeps the added mass low and biased downward so the axle assembly helps the model retain grip on rough, uneven ground while crawling.

The upgrade increases the wheel hex to 23mm and raises each wheel's downward mass to boost low-speed stability and climbing angle when the chassis meets depressions or steep obstacles. The assembly is intended for RC wheels with a 58mm inner diameter and a wheel thread hole sized for 5mm fasteners. Weight of a single pendulum plus hex is specified as 225 grams by the source material supplied with the product.

Packing includes

  • Pendulum Wheel Weight - 2pcs
  • 23mm Hex Adapter - 2pcs
  • M4x2.5x11 Screw Pin - 2pcs
  • 5mm Spring Steel Shims - 2pcs
  • 5mm Metal Washer - 2pcs
  • 20mm Stainless Steel Hex Socket Screws - 2pcs

Compatible Models

  • TRAXXAS TRX-4 MERCEDES-BENZ G500 82096-4

Fit these pendulum weights when you want extra low-mounted mass to improve crawling traction and angle support on TRX-4 MERCEDES-BENZ models; always verify wheel inner diameter and thread hole size before installation.

What wheel specs are required for these pendulum weights?

You need wheels with a 58mm inner diameter and a 5mm wheel thread hole to accept the supplied 23mm hex adapter and fasteners; check your wheel measurements before ordering.

How do these attach to the knuckle arms?

The unit mounts over the outer case of the front and rear knuckle arms and secures to the 23mm hex; the pendulum sits outboard and low to shift the center of gravity down during articulation.

Does the pendulum use bearings?

Yes, it uses a central bearing combined with a Delrin collar to permit the pendulum to swing and maintain a lower center of mass as the axle articulates.

Will this affect handling on flatter surfaces?

You may notice increased low-speed traction and a tendency for the vehicle to stay lower during articulation; adjust suspension preload or ride height if needed for balanced handling on flat runs.

Are replacement parts available for the kit components?

The kit contains standard fasteners and shims that can be replaced from common RC supply sources; keep the M4 pins and 20mm hex socket screws for future service.

Copyright © 2008-2026 rcjaz.ca All rights reserved