GPM TRAXXAS 1/8 X-Maxx 22mm Aluminium Wheel Cone Locker TXM005N - RC Spare Part  [TXM005N]

TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N
Price:
CAD$30.31
Brand:
GPM
Model:
TXM005N
GTIN:
4894538036565
Condition:
Brand New
Write a review
alt="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N" title="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N"
alt="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N" title="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N"
alt="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N" title="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N"
alt="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N" title="TRAXXAS 1/8 X-Maxx Aluminium 22mm Wheel Cone Locker - 4pcs - GPM TXM005N"

Aluminium cone retainers for X-Maxx hubs

This aluminium cone wheel locker is an aftermarket replacement made for TRAXXAS 1/8 X-Maxx vehicles. The tapered cone locates and compresses the wheel assembly against the hub, helping to keep wheels properly seated during high speed runs and heavy off-road loads.

Supplied as a matched set of 4 pieces sized for a 22mm wheel hex interface, each part receives an anodized surface for corrosion resistance and consistent fit. Installation follows standard X-Maxx hub access and the cone profile is intended to seat without modifying the hub geometry.

Specifications

  • Item: Wheel Cone Locker, 22mm, 4pcs
  • Material: Aluminium
  • Model Number: TXM005N
  • Compatibility: TRAXXAS 1/8 X-Maxx

Fit these aluminium cone lockers when replacing worn plastic retainers or when upgrading to anodized hardware to achieve repeatable preload and secure wheel seating on TRAXXAS X-Maxx machines.

This item is compatible with

  • TRAXXAS XMAXX
  • TRAXXAS X MAXX 8S Monster Truck

Will these fit TRAXXAS 1/8 X-Maxx 22mm hex hubs?

Yes. The parts are sized for a 22mm wheel hex interface and are intended for TRAXXAS 1/8 X-Maxx hubs that accept that standard. Verify hub clearance before final assembly.

What torque or fastening method should I use?

Use the original wheel nut or retaining hardware and tighten to the vehicle manufacturer recommended torque. Ensure the cone fully seats against the hub and check wheel play after a short test run.

How do I care for the anodized finish?

Rinse off mud and grit after wet or salty runs, avoid abrasive cleaners, and inspect for nicks or burrs that could affect seating. Routine checks keep fit consistent.

Can these replace the factory plastic cones?

Yes. They are intended as aluminium replacements to provide more consistent seating and greater wear resistance compared with typical plastic wheel cones.

Copyright © 2008-2026 rcjaz.ca All rights reserved